View ISL6615AFRZ_4276176.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 isl6615a high-frequency 6a sink synchronous mosfet drivers with protection features isl6615a the isl6615a is a high-speed mosfet driver optimized to drive upper and lower power n-channel mosfets in a synchronous rectified buck converter topology. this driver, combined with an intersil digital or analog multiphase pwm controller, forms a complete high frequency and high effici ency voltage regulator. the isl6615a drives both upper and lower gates over a range of 4.5v to 13.2v. this drive-voltage provides the flexibility necessary to optimize applications involving trade-offs between gate charge and conduction losses. the isl6615a features 6a typical sink current for the low-side gate driver, enhancing the lower mosfet gate hold-down capability during phase node rising edge, preventing power loss caused by the self turn-on of the lower mosfet due to the high dv/dt of the switching node. an advanced adaptive zero shoot-through protection is integrated to prevent both the upper and lower mosfets from conducting simultaneously and to minimize the dead-time. the isl6615a includes an overvoltage protection feature operational before vcc exceeds its turn-on threshold, at which the phase node is connected to the gate of the low side mosfet (lgate). the output voltage of the converter is then limited by the threshold of the low side mosfet, which provides some protection to the load if the upper mosfet(s) is shorted. the isl6615a also features an input that recognizes a high-impedance state, work ing together with intersil multiphase pwm controllers to prevent negative transients on the controlled output voltage when operation is suspended. this feature eliminates the need for the schottky diode that may be utilized in a power system to protect the load from negative output voltage damage. features ? dual mosfet drives for synchronous rectified bridge ? advanced adaptive zero shoot-through protection - body diode detection -lgate detection -auto-zero of r ds(on) conduction offset effect ? adjustable gate voltage for optimal efficiency ? 36v internal bootstrap schottky diode ? bootstrap capacitor overcharging prevention ? supports high switching frequency (up to 1mhz) - 6a lgate sinking current capability - fast rise/fall times and low propagation delays ? support 5v pwm input logic ? tri-state pwm input for safe output stage shutdown ? tri-state pwm input hysteresis for applications with power sequencing requirement ? pre-por overvoltage protection ? vcc undervoltage protection ? expandable bottom copper pad for better heat spreading ? dual flat no-lead (dfn) package - near chip-scale package footprint; improves pcb efficiency and thinner in profile ? pb-free (rohs compliant) applications* (see page 10) ? optimized for pol dc/dc converters for iba systems ? core regulators for intel? and amd? microprocessors ? high current low-profile dc/dc converters ? high frequency and high efficiency vrm and vrd ? synchronous rectification for isolated power supplies related literature* (see page 10) technical brief tb363 ?guidelines for handling and processing moisture sensitive surface mount devices (smds)? technical brief tb389 ?pcb land pattern design and surface mount guidelines for qfn packages? caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | intersil (and design) is a registered trademark of intersil americas inc. copyright intersil americas inc. 2008, 2010. all rights reserved all other trademarks mentioned are the property of their respective owners. april 22, 2010 fn6608.1
2 fn6608.1 april 22, 2010 typical application - 2 channel converter block diagram isl6615a pvcc vcc pwm +5v 10k 8k boot ugate phase lgate gnd uvcc = pvcc control logic por/ shoot- through protection pre-por ovp (lvcc) (uvcc) features substrate resistance for dfn devices, the pad on the bottom side of the package must be soldered to the circuit?s ground. pad +7v to +13.2v boot ugate phase lgate pwm vcc pvcc v in +v core pgood vid fs/en gnd isen2 isen1 pwm2 pwm1 vsen pwm fb vcc +5v comp isl6615a control +5v (isl63xx (optional) or isl65xx) +7v to +13.2v boot ugate phase lgate pwm vcc pvcc v in isl6615a gnd gnd the isl6615a can support 5v pwm input isl6615a
3 fn6608.1 april 22, 2010 ordering information part number (notes 1, 2, 3) part marking temp. range (c) package (pb-free) pkg. dwg. # isl6615acbz 6615a cbz 0 to +70 8 ld soic m8.15 isl6615acrz 615a 0 to +70 10 ld 3x3 dfn l10.3x3 isl6615aibz 6615a ibz -40 to +85 8 ld soic m8.15 isl6615airz 15ai -40 to +85 10 ld 3x3 dfn l10.3x3 ISL6615AFRZ 15af -40 to +125 10 ld 3x3 dfn l10.3x3 notes: 1. add ?-t? suffix for tape and reel. please refer to tb347 for details on reel specifications. 2. these intersil pb-free plastic packaged products employ special pb-free material sets, molding compounds/die attach materials, and 100% matte tin pl ate plus anneal (e3 termination finish, which is rohs compliant and compatible with both snpb and pb-free soldering operations). inte rsil pb-free products are msl classified at pb-free peak reflow temperatures that meet or exceed the pb-free requirements of ipc/jedec j std-020. 3. for moisture sensitivity level (msl), please see device in formation page for isl6615a . for more information on msl please see techbrief tb363 . pin configurations isl6615a (8 ld soic) top view isl6615a (10 ld 3x3 dfn) top view ugate boot pwm gnd 1 2 3 4 8 7 6 5 phase pvcc vcc lgate ugate boot n/c pwm phase pvcc n/c vcc gnd lgate gnd c ommand to connect pin 3 to gnd and pin 8 to pvcc 2 3 4 1 5 9 8 7 10 6 functional pin descriptions package pin # pin symbol function soic dfn 1 1 ugate upper gate drive output. connect to gate of high-side po wer n-channel mosfet. 2 2 boot floating bootstrap supply pin fo r the upper gate drive. connect th e bootstrap capacitor between this pin and the phase pin. the bootstrap capacitor prov ides the charge to turn on the upper mosfet. see the internal bootstrap device ?timing diagra m? on page 6 under description for guidance in choosing the capacitor value. - 3, 8 n/c no connection. recommend to connect pin 3 to gnd and pin 8 to pvcc. 3 4 pwm the pwm signal is the control input for the driver. the pwm signal can enter three distinct states during operation, see the ?timing diagram? on page 6 section under description for further details. connect this pin to the pwm output of the controller. 4 5 gnd bias and reference ground. all sign als are referenced to this node. it is also the power ground return of the driver. 5 6 lgate lower gate drive output. connect to ga te of the low-side power n-channel mosfet. 6 7 vcc its operating range is +6.8v to 13.2v. place a high quality low esr ceramic capacitor from this pin to gnd. 7 9 pvcc this pin supplies power to both upper and lower gate drives. its op erating range is +4.5v to 13.2v. place a high quality low esr cerami c capacitor from this pin to gnd. 8 10 phase connect this pin to the source of the upper mosfet and the drain of the lower mosfet. this pin provides a return path for the upper gate drive. 9 11 pad connect this pad to the power ground pl ane (gnd) via thermally enhanced connection. isl6615a
4 fn6608.1 april 22, 2010 absolute maximum ratings thermal information supply voltage (vcc) . . . . . . . . . . . . . . . . . . . . . . . . . 15v supply voltage (pvcc) . . . . . . . . . . . . . . . . . . .vcc + 0.3v boot voltage (vboot-gnd) . . . . . . . . . . . . . . . . . . . . 36v input voltage (vpwm). . . . . . . . . . . . . . . .gnd - 0.3v to 7v ugate . . . . . . . . . . . . . vphase - 0.3vdc to vboot + 0.3v vphase - 3.5v (<100ns pulse width, 2j) to vboot + 0.3v lgate . . . . . . . . . . . . . . . . gnd - 0.3vdc to vpvcc + 0.3v . . . . gnd - 5v (<100ns pulse width, 2j) to vpvcc + 0.3v phase . . . . . . . . . . . . . . . . . . . . .gnd - 0.3vdc to 15vdc gnd - 8v (<400ns, 20j) to . . . . . . . . . . . . . . . . . . 30v (<200ns, vboot-gnd < 36v)) esd rating human body model . . . . . . . . . . . . . . . . class i jedec std thermal resistance . . . . . . . . . . . . . . ja (c/w) jc (c/w) soic package (note 4) . . . . . . . . . . 98 n/a dfn package (notes 5, 6) . . . . . . . . 47 5 maximum junction temperature (plastic package) . . +150c maximum storage temperature range . . . -65c to +150c pb-free reflow profile . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/pb-freereflow.asp recommended operating conditions ambient temperature range isl6615acrz, isl6615acbz. . . . . . . . . . . . 0c to +70c isl6615airz, isl6615aibz . . . . . . . . . . -40c to +85c ISL6615AFRZ (note 7) . . . . . . . . . . . . . -40c to +125c maximum operating junction temperature. . . . . . . . +125c vcc supply voltage. . . . . . . . . . . . . . . . . . . . 6.8v to 13.2v pvcc supply voltage . . . . . . . . . . . . . . . . 5v to 12v 10% caution: do not operate at or near the maximum ratings listed for extended periods of time. exposure to such conditions may adv ersely impact product reliability and result in failures not covered by warranty. notes: 4. ja is measured with the component mounted on a high effective thermal conductivi ty test board in free air. 5. ja is measured in free air with the component mounted on a high effective thermal conductivity test board with ?direct attach? features. see tech brief tb379. 6. for jc , the ?case temp? location is the center of the exposed metal pad on the package underside. 7. when using ISL6615AFRZ, care should be taken to minimize power dissipation. electrical specifications recommended operating conditions; boldface limits apply over the operating temperature ranges. parameter symbol test conditions min (note 8) typ max (note 8) units vcc supply current bias supply current i vcc f pwm = 300khz, v vcc = 12v - 4.5 - ma gate drive bias current i pvcc f pwm = 300khz, v pvcc = 12v - 8 - ma power-on reset and enable vcc rising threshold 6.1 6.4 6.7 v vcc falling threshold 4.7 5.0 5.3 v pwm input (see ?timing diagram? on page 6) input current i pwm v pwm = 5v - 510 - a v pwm = 0v - -475 - a pwm rising threshold (note 9) vcc = 12v - 3.00 - v pwm falling threshold (note 9) vcc = 12v - 2.00 - v typical tri-state shutdown window vcc = 12v 1.80 - 2.40 v tri-state lower gate falling threshold vcc = 12v - 1.50 - v tri-s tat e lowe r g ate ri si ng threshold vcc = 12v - 1.00 - v tri-state upper gate rising threshold vcc = 12v - 3.20 - v tri-state upper gate falling threshold vcc = 12v - 2.70 - v shutdown holdoff time t tsshd -55- ns isl6615a
5 fn6608.1 april 22, 2010 ugate rise time (note 9) t ru v pvcc = 12v, 3nf load, 10% to 90% - 13 - ns lgate rise time (note 9) t rl v pvcc = 12v, 3nf load, 10% to 90% - 10 - ns ugate fall time (note 9) t fu v pvcc = 12v, 3nf load, 90% to 10% - 10 - ns lgate fall time (note 9) t fl v pvcc = 12v, 3nf load, 90% to 10% - 10 - ns ugate turn-on propagation delay (note 9) t pdhu v pvcc = 12v, 3nf load, adaptive - 30 - ns lgate turn-on propagation delay (note 9) t pdhl v pvcc = 12v, 3nf load, adaptive - 20 - ns ugate turn-off propagation delay (note 9) t pdlu v pvcc = 12v, 3nf load - 10 - ns lgate turn-off propagation delay (note 9) t pdll v pvcc = 12v, 3nf load - 20 - ns lg/ug tri-state propagation delay (note 9) t pdts v pvcc = 12v, 3nf load - 20 - ns output (note 9) upper drive source current i u_source v pvcc = 12v, 3nf load - 2.5 - a upper drive source impedance r u_source 150ma source current - 1 - upper drive sink current i u_sink v pvcc = 12v, 3nf load - 4 - a upper drive sink impedance r u_sink 150ma sink current - 0.8 - lower drive source current i l_source v pvcc = 12v, 3nf load - 4 - a lower drive source impedance r l_source 150ma source current - 0.7 - lower drive sink current i l_sink v pvcc = 12v, 3nf load - 6 - a lower drive sink impedance r l_sink 150ma sink current - 0.45 - notes: 8. parameters with min and/or max limits are 100% tested at +2 5c, unless otherwise specified. temperature limits established by characterization and are not production tested. 9. limits establishe d by characterization and ar e not production tested. electrical specifications recommended operating conditions; boldface limits apply over the operating temperature ranges. (continued) parameter symbol test conditions min (note 8) typ max (note 8) units isl6615a
6 fn6608.1 april 22, 2010 description operation designed for versatility an d speed, the isl6615a mosfet driver controls both high-side and low-side n-channel fets of a half-bridge power train from one externally provided pwm signal. prior to vcc exceeding its por level, the pre-por overvoltage protection function is activated during initial start-up; the upper gate (ugate) is held low and the lower gate (lgate), controlled by the pre-por overvoltage protection circuits, is connected to the phase. once the vcc voltage surpasses the vcc rising threshold (see ?electrical specifications? on page 4) the pwm signal takes control of gate transitions. a rising edge on pwm initiates the turn-off of the lower mosfet (see ?timing diagram? on page 6). after a short propagation delay [t pdll ], the lower gate begins to fall. typical fall times [t fl ] are provided in the ?electrical specifications? on page 4. adaptive shoot-through circuitry monitors the lgate voltage and determines the upper gate delay time [t pdhu ]. this prevents both the lower and upper mosfets from conducting simultaneously. once this delay period is complete, the upper gate drive begins to rise [t ru ] and the upper mosfet turns on. a falling transition on pwm results in the turn-off of the upper mosfet and the turn-on of the lower mosfet. a short propagation delay [t pdlu ] is encountered before the upper gate begins to fall [t fu ]. again, the adaptive shoot-through circuitry determines the lower gate delay time, t pdhl . the phase voltage and the ugate voltage are monitored, and the lower ga te is allowed to rise after phase drops below a level or the voltage of ugate to phase reaches a level depending upon the current direction (see the following section titled ?advanced adaptive zero shoot-through dead-time control? for details). the lower gate then rises [t rl ], turning on the lower mosfet. advanced adaptive zero shoot-through dead-time control the isl6615a driver incorporates a unique adaptive dead-time control technique to minimize dead-time, resulting in high efficiency from the reduced freewheeling time of the lower mosfets? body-diode conduction, and to prevent the upper and lower mosfets from conducting simultaneously. this is accomplished by ensuring the rising gate turns on its mosfet with minimum and sufficient delay after the other has turned off. during turn-off of the lower mosfet, the lgate voltage is monitored until it drops below 1.75v. prior to reaching this level, there is a 25ns blanking period to protect against sudden dips in the lgate voltage. once 1.75v is reached, the ugate is released to rise after 20ns of propagation delay. once the phase is high, the adaptive shoot-through circuitry monitors the phase and ugate voltages during pwm falling edge and subsequent ugate turn-off. if phase falls to less than +0.8v, the lgate is released to turn on after 10ns of propogation delay. if the ugate-phase falls to less than 1.75v and after 40ns of propogation delay, lgate is released to rise. tri-state pwm input a unique feature of these drivers and other intersil drivers is the addition of a shutdown window to the pwm input. if the pwm signal en ters and remains within the shutdown window for a set holdoff time, the driver outputs are disabled and both mosfet gates are pulled and held low. the shutdown state is removed when the pwm signal moves outside the shutdown window. otherwise, the pwm rising and falling thresholds outlined in electrical specifications on page 4, determine when the lower and upper gates are enabled. this feature helps prevent a negative transient on the output voltage when the output is shut down, eliminating the schottky diode that is used in some systems for protecting the load from reversed output voltage events. pwm ugate lgate t fl t pdhu t pdll t rl t tsshd t pdts t pdts 1.18v < pwm < 2.36v 0.76v < pwm < 1.96v t fu t ru t pdlu t pdhl t tsshd figure 1. timing diagram isl6615a
7 fn6608.1 april 22, 2010 in addition, more than 400mv hysteresis also incorporates into the tri-state shutdown window to eliminate pwm input oscillations due to the capacitive load seen by the pwm input through the body diode of the controller?s pwm output when the power-up and/or power-down sequence of bias supplies of the driver and pwm controller are required. power-on reset (por) function during initial start-up, the vcc voltage rise is monitored. once the rising vcc voltage exceeds 6.4v (typically), operation of the driver is enabled and the pwm input signal takes control of the gate drives. if vcc drops below the falling threshold of 5.0v (typically), operation of the driver is disabled. pre-por overvoltage protection prior to vcc exceeding its por level, the upper gate is held low and the lower gate is controlled by the overvoltage protection circuits. the upper gate driver is powered from pvcc and will be held low when a voltage of 2.75v or higher is present on pvcc as vcc surpasses its por threshold. the phase is connected to the gate of the low side mosfet (lgate), which provides some protection to the microprocessor if the upper mosfet(s) is shorted during start-up, normal, or shutdown conditions. for complete protection, the low side mosfet should have a gate threshold well below the maximum voltage rating of the load/microprocessor. internal bootstrap device both drivers feature an internal bootstrap schottky diode. simply adding an external capacitor across the boot and phase pins completes the bootstrap circuit. the bootstrap function is also designed to prevent the bootstrap capacitor from overcharging due to the large negative swing at the trailing-edge of the phase node. this reduces voltage stress on the boot to phase pins. the bootstrap capacitor must have a maximum voltage rating above pvcc + 5v and its capacitance value can be chosen from equation 1: where q g1 is the amount of gate charge per upper mosfet at v gs1 gate-source voltage and n q1 is the number of control mosfets. the vboot_cap term is defined as the allowable droop in the rail of the upper gate drive. as an example, suppose two irlr7821 fets are chosen as the upper mosfets. the gate charge, q g , from the data sheet is 10nc at 4.5v (v gs ) gate-source voltage. then the q gate is calculated to be 53nc for pvcc = 12v. we will assume a 200mv droop in drive voltage over the pwm cycle. we find that a bootstrap capacitance of at least 0.267f is required. the next larger standard value capacitance is 0.33f. a good quality ceramic capacitor is recommended. gate drive voltage versatility the isl6615a provides the user with flexibility in choosing the gate drive voltage for efficiency optimization. the isl6615a ties the upper and lower drive rails together. simply applying a voltage from +4.5v up to 13.2v on pvcc sets both gate drive rail voltages simultaneously, while vcc?s operating range is from +6.8v up to 13.2v. power dissipation package power dissipation is mainly a function of the switching frequency (f sw ), the output drive impedance, the external gate resistance and the selected mosfet?s internal gate resistance and total gate charge. calculating the power dissipation in the driver for a desired application is critical to ensure safe operation. exceeding the maximum allowable power dissipation level will push the ic beyond the maximum recommended operating junction temperature of +125c. the maximum allowable ic power dissipation for the so8 package is appr oximately 800mw at room temperature, while the power dissipation capacity in the dfn package (with an exposed heat escape pad) is more than 1.5w. the dfn package is more suitable for high frequency applications. see ?layout considerations? on page 8 for thermal transfer improvement suggestions. when designing the driver in to an application, it is recommended that the following calculation is used to ensure safe operation at the desired frequency for the selected mosfets. the total gate drive power losses due to the gate charge of mosfets and the driver?s internal circuitry and their corresponding average driver current can be estimated with equations 2 and 3, respectively: c boot_cap q gate v boot_cap -------------------------------------- q gate q g1 pvcc ? v gs1 ----------------------------------- - n q1 ? = (eq. 1) 50nc 20nc figure 2. bootstrap capacitance vs boot ripple voltage c boot_cap ( f) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.3 0.0 0.1 0.2 0.4 0.5 0.6 0.9 0.7 0.8 1.0 q gate = 100nc 1.6 v boot_cap (v) isl6615a
8 fn6608.1 april 22, 2010 where the gate charge (q g1 and q g2 ) is defined at a particular gate to source voltage (v gs1 and v gs2 ) in the corresponding mosfet datasheet; iq is the driver?s total quiescent current with no load at both drive outputs; n q1 and n q2 are the number of upper and lower mosfets, respectively; pvcc is the drive voltage for both upper and lower fets. the iq*vcc product is the quiescent power of the driver without capacitive load and is typically 200mw at 300khz and vcc = pvcc = 12v. the total gate drive power losses are dissipated among the resistive components along the transition path. the drive resistance dissipates a portion of the total gate drive power losses, the rest will be dissipated by the external gate resistors (r g1 and r g2 ) and the internal gate resistors (r gi1 and r gi2 ) of mosfets. figures 3 and 4 show the typical uppe r and lower gate drives turn-on transition path. the power dissipation on the driver can be roughly estimated, as shown in equation 4. application information layout considerations the parasitic inductances of the pcb and of the power devices? packaging (both upper and lower mosfets) can cause serious ringing, exceeding the absolute maximum ratings of the devices. a good layout helps reduce the ringing on the switching node (phase) and significantly lower the stress applied to the output drives. the following advice is meant to lead to an optimized layout and performance: ? keep decoupling loops (vcc-gnd, pvcc-gnd and boot-phase) short and wide (at least 25 mils). avoid using vias on decoupling components other than their ground terminals, which should be on a copper plane with at least two vias. ? minimize trace inductance, especially on low- impedance lines. all power traces (ugate, phase, lgate, gnd, pvcc, vcc, gnd) should be short and wide (at least 25 mils). try to place power traces on a single layer, otherwise, two vias on interconnection are preferred where possible. for no connection (nc) pins on the qfn part, connect it to the adjacent net (lgate2/phase2) can reduce trace inductance. ? shorten all gate drive loops (ugate-phase and lgate-gnd) and route them closely spaced. ? minimize the inductance of the phase node. ideally, the source of the upper and the drain of the lower mosfet should be as close as thermally allowable. ? minimize the current loop of the output and input power trains. short the source connection of the lower mosfet to ground as close to the transistor pin as feasible. input capacitors (especially ceramic decoupling) should be placed as close to the drain of upper and source of lower mosfets as possible. ? avoid routing relatively high impedance nodes (such as pwm and enable lines) close to high dv/dt ugate and phase nodes. in addition, for heat spreading, place copper underneath the ic whether it has an exposed pad or not. the copper area can be extended beyond the bottom area of the ic and/or connected to buried power ground plane(s) with figure 3. typical upper-gate drive turn-on path p qg_tot p qg_q1 p qg_q2 i q vcc ? ++ = (eq. 2) p qg_q1 q g1 pvcc 2 ? v gs1 -------------------------------------- - f sw ? n q1 ? = p qg_q2 q g2 pvcc 2 ? v gs2 -------------------------------------- - f sw ? n q2 ? = i dr q g1 pvcc n q1 ? ? v gs1 ----------------------------------------------------- q g2 pvcc n q2 ? ? v gs2 ----------------------------------------------------- + ?? ?? ?? f sw i q + ? = (eq. 3) p dr p dr_up p dr_low i q vcc ? ++ = (eq. 4) p dr_up r hi1 r hi1 r ext1 + -------------------------------------- r lo1 r lo1 r ext1 + ---------------------------------------- + ?? ?? ?? p qg_q1 2 --------------------- ? = p dr_low r hi2 r hi2 r ext2 + -------------------------------------- r lo2 r lo2 r ext2 + ---------------------------------------- + ?? ?? ?? p qg_q2 2 --------------------- ? = r ext1 r g1 r gi1 n q1 ------------- + = r ext2 r g2 r gi2 n q2 ------------- + = q1 d s g r gi1 r g1 boot r hi1 c ds c gs c gd r lo1 phase pvcc figure 4. typical lower-gate drive turn-on path pvcc q2 d s g r gi2 r g2 r hi2 c ds c gs c gd r lo2 isl6615a
9 fn6608.1 april 22, 2010 thermal vias. this combination of vias for vertical heat escape, extended copper plane, and buried planes for heat spreading allows the ic to achieve its full thermal potential. upper mosfet self turn-on effects at start-up should the driver have insufficient bias voltage applied, its outputs are floating. if the input bus is energized at a high dv/dt rate while the driver outputs are floating due to the self-coupling via the internal c gd of the mosfet, the ugate could momentarily rise up to a level greater than the threshold voltage of the mosfet. this could potentially turn on the up per switch and result in damaging inrush energy. therefore, if such a situation (when input bus powered up before the bias of the controller and driver is ready) could conceivably be encountered, it is a common practice to place a resistor (r ugph ) across the gate and source of the upper mosfet to suppress the mille r coupling effect. the value of the resistor depends mainly on the input voltage?s rate of rise, the c gd /c gs ratio, as well as the gate-source threshold of the upper mosfet. a higher dv/dt, a lower c ds /c gs ratio, and a lower gate-source threshold upper fet will require a smaller resistor to diminish the effect of the internal capacitive coupling. for most applications, the integrated 20k typically sufficient, not affecting normal performance and efficiency. the coupling effect can be roughly estimated with the formulas in equation 5, which assume a fixed linear input ramp and neglect the clamping effect of the body diode of the upper drive and the bootstrap capacitor. other parasitic components such as lead inductances and pcb capacitances are also not taken into account. these equations are provided for guidance purpose only. therefore, the actual coupling effect should be examined using a very high impedance (10m or greater) probe to ensure a safe design margin. v gs_miller dv dt ------- rc rss 1e v ? ds dv dt ------- rc ? iss ? --------------------------------- - ? ?? ?? ?? ?? ?? ?? ?? = rr ugph r gi + = c rss c gd = c iss c gd c gs + = (eq. 5) figure 5. gate-to-source resistor to reduce upper mosfet miller coupling vin q upper d s g r gi r ugph boot du c ds c gs c gd dl phase pvcc isl6615a c boot ugate isl6615a
10 fn6608.1 april 22, 2010 products intersil corporation is a leader in the design and manuf acture of high-performance analog semiconductors. the company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. intersil's product families address power management and analog signal processing functions. go to www.intersil.com/products for a complete list of intersil product families. *for a complete listing of applications, related documentat ion and related parts, please see the respective device information page on intersil.com: isl6615a to report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff fits are available from our website at http://rel.intersil.com/reports/search.php revision history the revision history provided is for informat ional purposes only and is believed to be accurate, but not warranted. please go t o web to make sure you have the latest rev. date revision change 4/20/10 fn6608.1 electrial spec table changes: pwm input - shutdown holdoff time - typ from ?65? to ?55? ugate turn-on propagation delay (note 9) tpdhu vpvcc = 12v, 3nf load, adaptive - from ?10? to ?30? - ns lgate turn-on propagation delay (note 9) tp dhl vpvcc = 12v, 3nf load, adaptive - from ?10? to ?20? - ns lgate turn-off propagation delay (note 9) tpdll vpvcc = 12v, 3nf load, adaptive - from ?10? to ?20? - ns lg/ug tri-state propagation de lay (note 9) tpdts vpvcc = 12v, 3nf load, adaptive - from ?10? to ?20? - ns 2/24/10 converted to new intersil template. updated ordering info rmations industrial parts temp range from "-40c to +70c" to "-40c to +85c". added msl note. updated thermal information tja and tjc to match asyd in intrep id for soic - from "100, n/a" to "98, n/a" dfn - "48, 7" to "47, 5". moved over-temp note from conditions to end of spec table as "note". added bold text to conditio ns indicating over-temp. min and max columns added note reference. changed layout to meet new standa rd flow. added part # ISL6615AFRZ with temp range of -40c to +125c to ordering inform ation, recommended operating conditions and note 4 reference. updated pod l10.3x3 to latest revision. pod changes are as follows: changed note 4 from "dimension b a pplies..." to "lead width applies..." changed note callout in detail x from 4 to 5 changed height in side view from 0.90 max to 1.00 max added note 4 callout next to lead width in bottom view in land pattern, corrected lead shape for 4 corner pins to "l" shape (was rectangular and did not match bottom view). 04/30/08 fn6608.0 initial release to web isl6615a
11 fn6608.1 april 22, 2010 isl6615a package outline drawing l10.3x3 10 lead dual flat package (dfn) rev 6, 09/09 located within the zone indicated. the pin #1 indentifier may be unless otherwise specified, tolerance : decimal 0.05 tiebar shown (if present) is a non-functional feature. the configuration of the pin #1 id entifier is optional, but must be between 0.18mm and 0.30mm from the terminal tip. lead width applies to the metallized terminal and is measured dimensions in ( ) for reference only. dimensioning and tolerancing conform to amse y14.5m-1994. 6. either a mold or mark feature. 3. 5. 4. 2. dimensions are in millimeters. 1. notes: bottom view detail "x" side view typical recommended land pattern top view (4x) 0.10 index area pin 1 pin #1 index area c seating plane base plane 0.08 see detail "x" c c 5 6 6 a b 0.10 c 1 package 1.00 0.20 8x 0.50 2.00 3.00 (10x 0.23) (8x 0.50) 2.00 1.60 (10 x 0.55) 3.00 0.05 0.20 ref 10 x 0.23 10x 0.35 1.60 outline max (4x) 0.10 ab 4 c m 0.415 0.23 0.35 0.200 2 4
12 intersil products are manufactured, assembled and tested utilizing iso9000 qu ality systems as noted in the quality certifications found at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, th e reader is cautioned to verify that data sheets are current before placing orders. information furnished by intersil is believed to be accura te and reliable. however, no re sponsibility is assumed by inte rsil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which ma y result from its use. no licen se is granted by implication o r otherwise under any patent or patent rights of intersil or its subsidiaries. for information regarding intersil corporation and its products, see www.intersil.com fn6608.1 april 22, 2010 for additional products, see www.intersil.com/product_tree isl6615a small outline plast ic packages (soic) index area e d n 123 -b- 0.25(0.010) c a m bs e -a- l b m -c- a1 a seating plane 0.10(0.004) h x 45 c h 0.25(0.010) b m m notes: 1. symbols are defined in the ?m o series symbol list? in sec- tion 2.2 of publication number 95. 2. dimensioning and tole rancing per ansi y14.5m - 1982. 3. dimension ?d? does not includ e mold flash, protrusions or gate burrs. mold flash, protru sion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. dimension ?e? does not include interlead flash or protrusions. interlead flash and protrusi ons shall not exceed 0.25mm (0.010 inch) per side. 5. the chamfer on the body is optional. if it is not present, a vi- sual index feature must be located within the crosshatched area. 6. ?l? is the length of terminal for soldering to a substrate. 7. ?n? is the number of terminal positions. 8. terminal numbers are shown for reference only. 9. the lead width ?b?, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maxi- mum value of 0.61mm (0.024 inch). 10. controlling dimension: millim eter. converted inch dimen- sions are not necessarily exact. m8.15 (jedec ms-012-aa issue c) 8 lead narrow body small outline plastic package symbol inches millimeters notes min max min max a 0.0532 0.0688 1.35 1.75 - a1 0.0040 0.0098 0.10 0.25 - b 0.013 0.020 0.33 0.51 9 c 0.0075 0.0098 0.19 0.25 - d 0.1890 0.1968 4.80 5.00 3 e 0.1497 0.1574 3.80 4.00 4 e 0.050 bsc 1.27 bsc - h 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 l 0.016 0.050 0.40 1.27 6 n8 87 0 8 0 8 - rev. 1 6/05

▲Up To Search▲

Price & Availability of ISL6615AFRZ

	To Download ISL6615AFRZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .